Back to Release page

Release Notes for STM32F446ZE-Nucleo Examples

Copyright 2017 STMicroelectronics

 

Update History

V1.1.2 / 29-December-2017

Main Changes

  • Update stm32f4xx_hal_conf.h files to add support to HAL CAN Legacy Module.

V1.1.1 / 06-October-2017

Main Changes

  • Remove DATE and VERSION from the header of all the files.
  • Update RTC_Calendar example to reset handle RTC state when initializing:
    • main.c:  Add a call for HAL_RTC_RESET_HANDLE_STATE()

V1.1.0 / 17-February-2017

      Main Changes
  • Add missing APBPrescTable[8] table in system_stm32f4xx.c file
  • Fix refresh period in WWDG_Example example readme file
  • Update BSP example to be aligned with new HAL SD and BSP Drivers implementation
  • Update stm32f4xx_hal_conf.h file in overall examples to remove unnecessary ETH PHY configuration
  • Update TIM_OCToggle readme file to be aligned with TIM configuration
  • Use DMA FIFO mode instead of Direct mode in DMA_FLASHToRAM example

V1.0.2 / 06-May-2016

      Main Changes
  • Add new define USE_SPI_CRC in stm32f4xx_hal_conf.h file for code cleanup when the CRC calculation is disabled
  • Add two new time base examples
  • Update HAL_TimeBase example to use TIM HW as time base source instead of Systick
  • Update FLASH_EraseProgram example to cover all flash sectors
  • Update IWDG example to be in line with latest updates done on HAL IWDG drivers
    • Remove the HAL_IWDG_Start function in the main.c file
  • Update WWDG examples to be in line with latest updates done on HAL WWDG drivers
    • Remove the HAL_WWDG_Start and update the HAL_WWDG_Refresh functions in the main.c file
    • Remove HAL_WWDG_MspDeInit function from stm32f4xx_hal_msp.c file
  • Update DMA_FLASHToRAM example to use HAL_DMA_RegisterCallback() function
  • Update PWR_CurrentConsumption example as follows
    • Configure missing GPIO Ports as analog mode for sleep and stop modes
    • Add the case of under-drive mode to achieve the lowest possible current consumption

V1.0.1 / 29-January-2016

      Main Changes
  • stm32f4xx_hal_conf.h
    • Adjust the HSE Start-up Timeout value: 100ms instead of 5s
    • Add new define for the LSE start-up Timeout: LSE_STARTUP_TIMEOUT
  • HAL_TimeBase
    • Update to use new HAL TimeBase driver template stm32xxx_hal_timebase_time.c
  • RCC_ClockConfig
    • Alignment with STM32F4xx_HAL_Driver V1.4.4: update to use the new define for the HSI calibration default value

V1.0.0 / 13-November-2015

Main Changes

  • First official release

License

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
  1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
  3. Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived
       from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

For complete documentation on STM32 Microcontrollers visit www.st.com/STM32